免费建设网站制作,移动端网站seo,女生wordpress网站适合,中卫市网站开发制作HCIP HCIA一、知识回顾1、OSI七层参考模型#xff1a;2、重要的几个协议报头格式 二、静态实验1、实验拓扑图2、实验要求3、实验思路4、实验步骤1、给接口划分IP地址以及配置环回地址2、交换机配置划分VLAN3、配置静态路由4、配置DHCP服务5、测试6、优化 HCIA
1、七层参考模型… HCIP HCIA一、知识回顾1、OSI七层参考模型2、重要的几个协议报头格式 二、静态实验1、实验拓扑图2、实验要求3、实验思路4、实验步骤1、给接口划分IP地址以及配置环回地址2、交换机配置划分VLAN3、配置静态路由4、配置DHCP服务5、测试6、优化 HCIA
1、七层参考模型及IP讲解 2、TCP三次握手讲解 3、TCP四次挥手讲解及抓包分析 4、DHCP协议讲解及抓包分析 5、静态综合实验讲解 7、静态路由讲解 8、RIP路由信息协议讲解 9、动态路由协议讲解 10、抓包进行分析RIP以及OSPF的包 11、动态路由OSPF配置综合实验讲解 12、Vlan虚拟局域网技术讲解 13、ACL访问控制列表讲解 14、NAT技术讲解 15、网络综合实验讲解
一、知识回顾
1、OSI七层参考模型
物理层——定义电气电压接口规范光学特性 数据链路层
MAC媒介访问控制层LLC逻辑链路层为上层提供FCS校验
网络层——通过IP地址进行逻辑寻址代表设备路由器。 物理层数据链路层以及网络层能不能全网可达可以全网可达。 传输层——通过端口号区分不同的服务数据分段确认重传排序流控只针对于TCP。
TCP面向连接的可靠传输协议 面向连接 三次握手以及四次挥手主要体现 可靠 确认重传排序以及流控。 常见的四层协议 TCPUDP 常见的三层协议 IPICMPARPUDP非面向连接的不可靠传输协议
会话层——建立维持终止会话进程。 表示层——编码解码加密解密 应用层——实现人机交互的界面 数据封装以及解封装 以太网一类帧二类帧封装——IP——TCP/UDP——data数据包——FCS校验逻辑链路层提供 数据分段的标准MYU最大传输单元1500字节MSS最大段长度1480。原因是报头长度为20字节 TCP-IP协议栈与OSI模型对比
相同点 1、都是模型化层次 2、下层对上层提供服务支持 3、每层协议彼此相互独立不同点 1、TCP-IP协议栈先有协议后有模型只是使用于TCP-IP网络。 2、OSI七层参考模型先有模型后有协议。 3、层数不同 滑动窗口就是流控什么是滑动窗口其实是吞吐量的问题。 2、重要的几个协议报头格式
IPV4数据包结构 IPV4数据包格式
版本号 这4比特规定了数据报的IP协议版本。通过查看版本号路由器能够确定如何解释IP数据报的剩余部分。不同的IP版本使用不同的数据报格式。首部长度 因为IPV4数据报可包含一些可变数量的选项这些选项包括在IPV4数据报首部中故需要用这4个比特来确定IP数据报中载荷例如在这个数据报中被封装的运输层报文段实际开始的地方。大多数IP数据报不包含选项所以一般的IP数据报具有20字节的首部。服务类型 服务类型TOS比特包含在IPV4首部中以便使不同类型的IP数据报能相互与别开来例如将实时数据报如用于IP电话应用与非实时流量如FTP区分开也许是有用的。提供特定等级的服务是一个由网络管理员为路由器确定和配置的策略问题。数据报长度
二、静态实验
1、实验拓扑图 2、实验要求
1.全网可达2.拓扑中所需地址全部基于192.168.0.0/24划分所得3.静态路由不许使用其他动态4.R8环回需要汇总
3、实验思路
拓扑中所需地址基于192.168.0.0/24进行划分这里我们首先数图中需要多少个网段
骨干链路——6个网段R1的环回上——1个网段两个vlan——两个网段
所以我们首先进行划分网段
192.168.0.0/24需要划分9个网段——也就向后借位借4位
128-64-32-16-8-4-2-1
这里我们可以看到第四位为16
那么9个网段分别为
192.168.0.0/28——R1环回
192.168.0.16/28——骨干链路网段
192.168.0.32/28
192.168.0.48/28
192.168.0.64/28
192.168.0.80/28
192.168.0.96/28
192.168.0.112/28——两个vlan
192.168。0.128/28
剩下的作为保留网段而这里我们也需要对R1的环回进行划分由实验要求的拓扑图可知我们需要给它划分3个环回网段
192.168.0.0/28划分为3个网段我们需要向后借2位
也就成了
192.168.0.0/30
192.168.0.64/30
192.168.0.128/30
同时剩下的作为保留网段拓扑图如下
4、实验步骤 1、给接口划分IP地址以及配置环回地址
R1 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys R1
[R1]user
[R1]user-in
[R1]user-interface con
[R1]user-interface console 0
[R1-ui-console0]id
[R1-ui-console0]idle-timeout 0 0
[R1-ui-console0]quit
[R1]int g0/0/0
[R1-GigabitEthernet0/0/0]ip ad
[R1-GigabitEthernet0/0/0]ip address 192.168.0.17 28
Jul 17 2023 15:58:00-08:00 R1 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[R1-GigabitEthernet0/0/0]int g0/0/1
[R1-GigabitEthernet0/0/1]ip ad
[R1-GigabitEthernet0/0/1]ip address 192.168.0.97 28
Jul 17 2023 15:58:16-08:00 R1 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP
on the interface GigabitEthernet0/0/1 has entered the UP state.
[R1-GigabitEthernet0/0/1]quit
[R1]int l
[R1]int LoopBack 0
[R1-LoopBack0]ip ad
[R1-LoopBack0]ip address 192.168.0.1 30
[R1-LoopBack0]int l 1
[R1-LoopBack1]ip ad
[R1-LoopBack1]ip address 192.168.0.65 30
[R1-LoopBack1]int l 2
[R1-LoopBack2]ip ad
[R1-LoopBack2]ip address 192.168.0.129 30
[R1-LoopBack2]quit
[R1]查看结果全up
[R1]display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 6
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 6
The number of interface that is DOWN in Protocol is 1Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.0.17/28 up up
GigabitEthernet0/0/1 192.168.0.97/28 up up
GigabitEthernet0/0/2 unassigned down down
LoopBack0 192.168.0.1/30 up up(s)
LoopBack1 192.168.0.65/30 up up(s)
LoopBack2 192.168.0.129/30 up up(s)
NULL0 unassigned up up(s)
[R1]R2 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys R2
[R2]use
[R2]user-bind
[R2]user-group
[R2]user-interface con
[R2]user-interface console 0
[R2-ui-console0]id
[R2-ui-console0]idle-timeout 0 0
[R2-ui-console0]quit
[R2]int g0/0/0
[R2-GigabitEthernet0/0/0]ip ad
[R2-GigabitEthernet0/0/0]ip address 192.168.0.18 28
Jul 17 2023 16:08:37-08:00 R2 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[R2-GigabitEthernet0/0/0]int g0/0/1
[R2-GigabitEthernet0/0/1]ip ad
[R2-GigabitEthernet0/0/1]ip address 192.168.0.33 28
Jul 17 2023 16:08:54-08:00 R2 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP
on the interface GigabitEthernet0/0/1 has entered the UP state.
[R2-GigabitEthernet0/0/1]quit
[R2]查看结果
[R2]dis
[R2]display ip int
[R2]display ip interface b
[R2]display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 3
The number of interface that is DOWN in Physical is 1
The number of interface that is UP in Protocol is 3
The number of interface that is DOWN in Protocol is 1Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.0.18/28 up up
GigabitEthernet0/0/1 192.168.0.33/28 up up
GigabitEthernet0/0/2 unassigned down down
NULL0 unassigned up up(s)
[R2]R3 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys R3
[R3]USER
[R3]user-bind
[R3]user-group
[R3]user-interface CON
[R3]user-interface console 0
[R3-ui-console0]id
[R3-ui-console0]idle-timeout 0 0
[R3-ui-console0]int g0/0/0
[R3-GigabitEthernet0/0/0]ip ad
[R3-GigabitEthernet0/0/0]ip address 192.168.0.34 28
Jul 17 2023 16:11:15-08:00 R3 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[R3-GigabitEthernet0/0/0]int g0/0/1
[R3-GigabitEthernet0/0/1]ip ad
[R3-GigabitEthernet0/0/1]ip address 192.168.0.82 28
Jul 17 2023 16:11:34-08:00 R3 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP
on the interface GigabitEthernet0/0/1 has entered the UP state.
[R3-GigabitEthernet0/0/1]int g0/0/2
[R3-GigabitEthernet0/0/2]ip ad
[R3-GigabitEthernet0/0/2]ip address 192.168.0.49 28
Jul 17 2023 16:12:05-08:00 R3 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP
on the interface GigabitEthernet0/0/2 has entered the UP state.
[R3-GigabitEthernet0/0/2]int g4/0/0
[R3-GigabitEthernet4/0/0]ip ad
[R3-GigabitEthernet4/0/0]ip address 192.168.0.65 28
[R3-GigabitEthernet4/0/0]
Jul 17 2023 16:12:31-08:00 R3 %%01IFNET/4/LINK_STATE(l)[3]:The line protocol IP
on the interface GigabitEthernet4/0/0 has entered the UP state.
[R3-GigabitEthernet4/0/0]quit
[R3]查看结果
[R3]dis
[R3]display ip in
[R3]display ip interface b
[R3]display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 5
The number of interface that is DOWN in Physical is 3
The number of interface that is UP in Protocol is 5
The number of interface that is DOWN in Protocol is 3Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.0.34/28 up up
GigabitEthernet0/0/1 192.168.0.82/28 up up
GigabitEthernet0/0/2 192.168.0.49/28 up up
GigabitEthernet4/0/0 192.168.0.65/28 up up
GigabitEthernet4/0/1 unassigned down down
GigabitEthernet4/0/2 unassigned down down
GigabitEthernet4/0/3 unassigned down down
NULL0 unassigned up up(s)
[R3]R4 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys R4
[R4]us
[R4]user-bind
[R4]user-group
[R4]user-interface con
[R4]user-interface console 0
[R4-ui-console0]id
[R4-ui-console0]idle-timeout 0 0
[R4-ui-console0]quit
[R4]int g0/0/0
[R4-GigabitEthernet0/0/0]ip ad
[R4-GigabitEthernet0/0/0]ip address 192.168.0.81 28
Jul 17 2023 16:24:09-08:00 R4 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[R4-GigabitEthernet0/0/0]int g0/0/1
[R4-GigabitEthernet0/0/1]ip ad
[R4-GigabitEthernet0/0/1]ip address 192.168.0.98 28
Jul 17 2023 16:24:27-08:00 R4 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP
on the interface GigabitEthernet0/0/1 has entered the UP state.
[R4-GigabitEthernet0/0/1]int g0/0/2.1
[R4-GigabitEthernet0/0/2.1]ip ad
[R4-GigabitEthernet0/0/2.1]ip address 192.168.0.113 28
[R4-GigabitEthernet0/0/2.1]int g0/0/2.2
[R4-GigabitEthernet0/0/2.2]ip ad
[R4-GigabitEthernet0/0/2.2]ip address 192.168.0.129 28
[R4-GigabitEthernet0/0/2.2]quit
[R4]查看结果
[R4]dis
[R4]display ip in
[R4]display ip interface b
[R4]display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 6
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 3
The number of interface that is DOWN in Protocol is 3Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.0.81/28 up up
GigabitEthernet0/0/1 192.168.0.98/28 up up
GigabitEthernet0/0/2 unassigned up down
GigabitEthernet0/0/2.1 192.168.0.113/28 up down
GigabitEthernet0/0/2.2 192.168.0.129/28 up down
NULL0 unassigned up up(s)
[R4]R5 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys R5
[R5]user
[R5]user-bind
[R5]user-group
[R5]user-interface con
[R5]user-interface console 0
[R5-ui-console0]i
[R5-ui-console0]idle-timeout 0 0
[R5-ui-console0]int g0/0/1
[R5-GigabitEthernet0/0/1]ip ad
[R5-GigabitEthernet0/0/1]ip address 192.168.0.66 28
Jul 17 2023 16:27:58-08:00 R5 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/1 has entered the UP state.
[R5-GigabitEthernet0/0/1]int g0/0/0
[R5-GigabitEthernet0/0/0]ip ad
[R5-GigabitEthernet0/0/0]ip address 192.168.0.50 28
Jul 17 2023 16:28:22-08:00 R5 %%01IFNET/4/LINK_STATE(l)[1]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[R5-GigabitEthernet0/0/0]int g0/0/2
[R5-GigabitEthernet0/0/2]ip ad
[R5-GigabitEthernet0/0/2]ip address 100.1.1.2 24
[R5-GigabitEthernet0/0/2]
Jul 17 2023 16:28:39-08:00 R5 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP
on the interface GigabitEthernet0/0/2 has entered the UP state.
[R5-GigabitEthernet0/0/2]quit
[R5]查看结果
[R5]dis
[R5]display ip in
[R5]display ip interface b
[R5]display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 4
The number of interface that is DOWN in Physical is 0
The number of interface that is UP in Protocol is 4
The number of interface that is DOWN in Protocol is 0Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 192.168.0.50/28 up up
GigabitEthernet0/0/1 192.168.0.66/28 up up
GigabitEthernet0/0/2 100.1.1.2/24 up up
NULL0 unassigned up up(s)
[R5]R6 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys R6
[R6]user
[R6]user-bind
[R6]user-group
[R6]user-interface
[R6]user-interface con
[R6]user-interface console 0
[R6-ui-console0]i
[R6-ui-console0]idle-timeout 0 0
[R6-ui-console0]int g0/0/0
[R6-GigabitEthernet0/0/0]ip ad
[R6-GigabitEthernet0/0/0]ip address 100.1.1.1 24
Jul 17 2023 16:30:48-08:00 R6 %%01IFNET/4/LINK_STATE(l)[0]:The line protocol IP
on the interface GigabitEthernet0/0/0 has entered the UP state.
[R6-GigabitEthernet0/0/0]quit
[R6]dis 查看结果
[R6]dis
[R6]display ip in
[R6]display ip interface b
[R6]display ip interface brief
*down: administratively down
^down: standby
(l): loopback
(s): spoofing
The number of interface that is UP in Physical is 2
The number of interface that is DOWN in Physical is 2
The number of interface that is UP in Protocol is 2
The number of interface that is DOWN in Protocol is 2Interface IP Address/Mask Physical Protocol
GigabitEthernet0/0/0 100.1.1.1/24 up up
GigabitEthernet0/0/1 unassigned down down
GigabitEthernet0/0/2 unassigned down down
NULL0 unassigned up up(s)
[R6]2、交换机配置划分VLAN
SW1 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys SW
[Huawei]sys SW1
[SW1]vlan b
[SW1]vlan batch 2 3
Info: This operation may take a few seconds. Please wait for a moment...done.
[SW1]int g0
Jul 17 2023 16:35:23-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 6, the c
hange loop count is 0, and the maximum number of records is 4095./0/1
[SW1-GigabitEthernet0/0/1]p
[SW1-GigabitEthernet0/0/1]port l
[SW1-GigabitEthernet0/0/1]port link-t
[SW1-GigabitEthernet0/0/1]port link-type a
[SW1-GigabitEthernet0/0/1]port link-type access
[SW1-GigabitEthernet0/0/1]p
[SW1-GigabitEthernet0/0/1]port de
[SW1-GigabitEthernet0/0/1]port default vlan 2
[SW1-GigabitEthernet0/0/1]int g0/0
Jul 17 2023 16:35:43-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 7, the c
hange loop count is 0, and the maximum number of records is 4095./2
[SW1-GigabitEthernet0/0/2]p
[SW1-GigabitEthernet0/0/2]port l
[SW1-GigabitEthernet0/0/2]port link-t
[SW1-GigabitEthernet0/0/2]port link-type a
[SW1-GigabitEthernet0/0/2]port link-type access
[SW1-GigabitEthernet0/0/2]p
[SW1-GigabitEthernet0/0/2]port de
[SW1-GigabitEthernet0/0/2]port default vlan 3
[SW1-GigabitEthernet0/0/2]
Jul 17 2023 16:36:03-08:00 SW1 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 9, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW1-GigabitEthernet0/0/2]int g0/0/3
[SW1-GigabitEthernet0/0/3]p
[SW1-GigabitEthernet0/0/3]port l
[SW1-GigabitEthernet0/0/3]port link-t
[SW1-GigabitEthernet0/0/3]port link-type t
[SW1-GigabitEthernet0/0/3]port link-type trunk
[SW1-GigabitEthernet0/0/3]p
[SW1-GigabitEthernet0/0/3]port t
[SW1-GigabitEthernet0/0/3]port trunk a
[SW1-GigabitEthernet0/0/3]port trunk allow-pass
[SW1-GigabitEthernet0/0/3]port trunk allow-pass vlan 2 3
[SW1-GigabitEthernet0/0/3]quit
[SW1]输出结果
[SW1]dis
[SW1]display vlan
[SW1]display vlan
The total number of vlans is : 3
--------------------------------------------------------------------------------
U: Up; D: Down; TG: Tagged; UT: Untagged;
MP: Vlan-mapping; ST: Vlan-stacking;
#: ProtocolTransparent-vlan; *: Management-vlan;
--------------------------------------------------------------------------------VID Type Ports
--------------------------------------------------------------------------------
1 common UT:GE0/0/3(U) GE0/0/4(U) GE0/0/5(D) GE0/0/6(D) GE0/0/7(D) GE0/0/8(D) GE0/0/9(D) GE0/0/10(D) GE0/0/11(D) GE0/0/12(D) GE0/0/13(D) GE0/0/14(D) GE0/0/15(D) GE0/0/16(D) GE0/0/17(D) GE0/0/18(D) GE0/0/19(D) GE0/0/20(D) GE0/0/21(D) GE0/0/22(D) GE0/0/23(D) GE0/0/24(D) 2 common UT:GE0/0/1(U) TG:GE0/0/3(U) 3 common UT:GE0/0/2(U) TG:GE0/0/3(U) VID Status Property MAC-LRN Statistics Description
--------------------------------------------------------------------------------1 enable default enable disable VLAN 0001
2 enable default enable disable VLAN 0002
3 enable default enable disable VLAN 0003
[SW1]SW2 实现代码
Huaweisys
Enter system view, return user view with CtrlZ.
[Huawei]sys SW2
[SW2]int g0/0/
Jul 17 2023 16:38:55-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 4, the c
hange loop count is 0, and the maximum number of records is 4095.1
[SW2-GigabitEthernet0/0/1]p
[SW2-GigabitEthernet0/0/1]quit
[SW2]vlan b
[SW2]vlan batch 2 3
Info: This operation may take a few seconds. Please wait for a moment...done.
[SW2]int g0/0/1
[SW2-GigabitEthernet0/0/1]p
[SW2-GigabitEthernet0/0/1]port l
[SW2-GigabitEthernet0/0/1]port link-
Jul 17 2023 16:39:15-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 5, the c
hange loop count is 0, and the maximum number of records is 4095.t
[SW2-GigabitEthernet0/0/1]port link-type t
[SW2-GigabitEthernet0/0/1]port link-type trunk
[SW2-GigabitEthernet0/0/1]p
[SW2-GigabitEthernet0/0/1]port t
[SW2-GigabitEthernet0/0/1]port trunk a
[SW2-GigabitEthernet0/0/1]port trunk allow-pass vlan 2 3
Jul 17 2023 16:39:25-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 6, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW2-GigabitEthernet0/0/1]int g0/0/2
[SW2-GigabitEthernet0/0/2]p
[SW2-GigabitEthernet0/0/2]port l
[SW2-GigabitEthernet0/0/2]port link-t
[SW2-GigabitEthernet0/0/2]port link-type a
[SW2-GigabitEthernet0/0/2]port link-type access
Jul 17 2023 16:39:35-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 7, the c
hange loop count is 0, and the maximum number of records is 4095.
[SW2-GigabitEthernet0/0/2]p
[SW2-GigabitEthernet0/0/2]port de
[SW2-GigabitEthernet0/0/2]port default vlan 2
[SW2-GigabitEthernet0/0/2]int g0/0
Jul 17 2023 16:39:45-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 9, the c
hange loop count is 0, and the maximum number of records is 4095./2
[SW2-GigabitEthernet0/0/2]int g0/0/3
[SW2-GigabitEthernet0/0/3]p
[SW2-GigabitEthernet0/0/3]port l
[SW2-GigabitEthernet0/0/3]port link-t
[SW2-GigabitEthernet0/0/3]port link-type a
[SW2-GigabitEthernet0/0/3]port link-type access
[SW2-GigabitEthernet0/0/3]p
[SW2-GigabitEthernet0/0/3]port
[SW2-GigabitEthernet0/0/3]portsw
Jul 17 2023 16:39:55-08:00 SW2 DS/4/DATASYNC_CFGCHANGE:OID 1.3.6.1.4.1.2011.5.25
.191.3.1 configurations have been changed. The current change number is 10, the
change loop count is 0, and the maximum number of records is 40
Error: The interface is already a L2 interface.
[SW2-GigabitEthernet0/0/3]p
[SW2-GigabitEthernet0/0/3]port de
[SW2-GigabitEthernet0/0/3]port default v
[SW2-GigabitEthernet0/0/3]port default vlan 3
[SW2-GigabitEthernet0/0/3]quit
[SW2]查看结果
[SW2]dis
[SW2]display vlan
The total number of vlans is : 3
--------------------------------------------------------------------------------
U: Up; D: Down; TG: Tagged; UT: Untagged;
MP: Vlan-mapping; ST: Vlan-stacking;
#: ProtocolTransparent-vlan; *: Management-vlan;
--------------------------------------------------------------------------------VID Type Ports
--------------------------------------------------------------------------------
1 common UT:GE0/0/1(U) GE0/0/4(D) GE0/0/5(D) GE0/0/6(D) GE0/0/7(D) GE0/0/8(D) GE0/0/9(D) GE0/0/10(D) GE0/0/11(D) GE0/0/12(D) GE0/0/13(D) GE0/0/14(D) GE0/0/15(D) GE0/0/16(D) GE0/0/17(D) GE0/0/18(D) GE0/0/19(D) GE0/0/20(D) GE0/0/21(D) GE0/0/22(D) GE0/0/23(D) GE0/0/24(D) 2 common UT:GE0/0/2(U) TG:GE0/0/1(U) 3 common UT:GE0/0/3(U) TG:GE0/0/1(U) VID Status Property MAC-LRN Statistics Description
--------------------------------------------------------------------------------1 enable default enable disable VLAN 0001
2 enable default enable disable VLAN 0002
3 enable default enable disable VLAN 0003
[SW2]3、配置静态路由
R1 实现代码
[R1]ip ro
[R1]ip route
[R1]ip route-static 192.168.0.32 28 192.168.0.18
[R1]ip route-static 192.168.0.64 28 192.168.0.18
[R1]ip route-static 192.168.0.48 28 192.168.0.18
[R1]ip route-static 100.1.1.0 24 192.168.0.18
[R1]ip route-static 100.1.1.0 24 192.168.0.98
[R1]ip route-static 192.168.0.48 28 192.168.0.98
[R1]ip route-static 192.168.0.64 28 192.168.0.98
[R1]ip route-static 192.168.0.80 28 192.168.0.98
[R1]ip route-static 192.168.0.112 28 192.168.0.98
[R1]ip route-static 192.168.0.128 28 192.168.0.98
[R1]R2 实现代码
[R2]ip ro
[R2]ip route
[R2]ip route-static 192.168.0.0 28 192.168.0.17
[R2]ip route-static 192.168.0.96 28 192.168.0.17
[R2]ip route-static 192.168.0.112 28 192.168.0.17
[R2]ip route-static 192.168.0.128 28 192.168.0.17
[R2]ip route-static 192.168.0.128 28 192.168.0.34
[R2]ip route-static 192.168.0.112 28 192.168.0.34
[R2]ip route-static 192.168.0.80 28 192.168.0.34
[R2]ip route-static 192.168.0.64 28 192.168.0.34
[R2]ip route-static 192.168.0.48 28 192.168.0.34
[R2]ip route-static 100.1.1.0 24 192.168.0.34
[R2]R3 实现代码
[R3]ip ro
[R3]ip route
[R3]ip route-static 192.168.0.16 28 192.168.0.33
[R3]ip route-static 192.168.0.0 28 192.168.0.33
[R3]ip route-static 192.168.0.0 28 192.168.0.81
[R3]ip route-static 192.168.0.96 28 192.168.0.81
[R3]ip route-static 192.168.0.112 28 192.168.0.81
[R3]ip route-static 192.168.0.128 28 192.168.0.81
[R3]ip route-static 100.1.1.0 24 192.168.0.66
[R3]ip route-static 100.1.1.0 24 192.168.0.50
[R3]R4实现代码
[R4]ip ro
[R4]ip route
[R4]ip route-static 192.168.0.0 28 192.168.0.97
[R4]ip route-static 192.168.0.16 28 192.168.0.97
[R4]ip route-static 192.168.0.32 28 192.168.0.82
[R4]ip route-static 192.168.0.64 28 192.168.0.82
[R4]ip route-static 100.1.1.0 24 192.168.0.82
[R4]R5 实现代码
[R5]ip ro
[R5]ip route
[R5]ip route-static 192.168.0.32 28 192.168.0.65
[R5]ip route-static 192.168.0.32 28 192.168.0.49
[R5]ip route-static 192.168.0.80 28 192.168.0.49
[R5]ip route-static 192.168.0.80 28 192.168.0.65
[R5]ip route-static 192.168.0.16 28 192.168.0.65
[R5]ip route-static 192.168.0.16 28 192.168.0.49
[R5]ip route-static 192.168.0.96 28 192.168.0.49
[R5]ip route-static 192.168.0.96 28 192.168.0.65
[R5]ip route-static 192.168.0.0 28 192.168.0.65
[R5]ip route-static 192.168.0.0 28 192.168.0.49
[R5]ip route-static 192.168.0.112 28 192.168.0.49
[R5]ip route-static 192.168.0.112 28 192.168.0.65
[R5]ip route-static 192.168.0.128 28 192.168.0.65
[R5]ip route-static 192.168.0.128 28 192.168.0.49
[R5]R6实现代码
[R6]ip ro
[R6]ip route
[R6]ip route-static 192.168.0.64 28 100.1.1.2
[R6]ip route-static 192.168.0.48 28 100.1.1.2
[R6]ip route-static 192.168.0.32 28 100.1.1.2
[R6]ip route-static 192.168.0.80 28 100.1.1.2
[R6]ip route-static 192.168.0.96 28 100.1.1.2
[R6]ip route-static 192.168.0.16 28 100.1.1.2
[R6]ip route-static 192.168.0.0 28 100.1.1.2
[R6]ip route-static 192.168.0.112 28 100.1.1.2
[R6]ip route-static 192.168.0.128 28 100.1.1.2
[R6]查看结果 R1路由表
[R1]dis
[R1]display ip ro
[R1]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: PublicDestinations : 26 Routes : 29 Destination/Mask Proto Pre Cost Flags NextHop Interface100.1.1.0/24 Static 60 0 RD 192.168.0.18 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.98 GigabitEthernet 0/0/1127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0192.168.0.0/30 Direct 0 0 D 192.168.0.1 LoopBack0192.168.0.1/32 Direct 0 0 D 127.0.0.1 LoopBack0192.168.0.3/32 Direct 0 0 D 127.0.0.1 LoopBack0192.168.0.16/28 Direct 0 0 D 192.168.0.17 GigabitEthernet 0/0/0192.168.0.17/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.31/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.32/28 Static 60 0 RD 192.168.0.18 GigabitEthernet 0/0/0192.168.0.48/28 Static 60 0 RD 192.168.0.18 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.98 GigabitEthernet 0/0/1192.168.0.64/28 Static 60 0 RD 192.168.0.18 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.98 GigabitEthernet 0/0/1192.168.0.64/30 Direct 0 0 D 192.168.0.65 LoopBack1192.168.0.65/32 Direct 0 0 D 127.0.0.1 LoopBack1192.168.0.67/32 Direct 0 0 D 127.0.0.1 LoopBack1192.168.0.80/28 Static 60 0 RD 192.168.0.98 GigabitEthernet 0/0/1192.168.0.96/28 Direct 0 0 D 192.168.0.97 GigabitEthernet 0/0/1192.168.0.97/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.111/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.112/28 Static 60 0 RD 192.168.0.98 GigabitEthernet 0/0/1192.168.0.128/28 Static 60 0 RD 192.168.0.98 GigabitEthernet 0/0/1192.168.0.128/30 Direct 0 0 D 192.168.0.129 LoopBack2192.168.0.129/32 Direct 0 0 D 127.0.0.1 LoopBack2192.168.0.131/32 Direct 0 0 D 127.0.0.1 LoopBack2
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R1]R2路由表
[R2]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: PublicDestinations : 18 Routes : 20 Destination/Mask Proto Pre Cost Flags NextHop Interface100.1.1.0/24 Static 60 0 RD 192.168.0.34 GigabitEthernet 0/0/1127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0192.168.0.0/28 Static 60 0 RD 192.168.0.17 GigabitEthernet 0/0/0192.168.0.16/28 Direct 0 0 D 192.168.0.18 GigabitEthernet 0/0/0192.168.0.18/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.31/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.32/28 Direct 0 0 D 192.168.0.33 GigabitEthernet 0/0/1192.168.0.33/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.47/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.48/28 Static 60 0 RD 192.168.0.34 GigabitEthernet 0/0/1192.168.0.64/28 Static 60 0 RD 192.168.0.34 GigabitEthernet 0/0/1192.168.0.80/28 Static 60 0 RD 192.168.0.34 GigabitEthernet 0/0/1192.168.0.96/28 Static 60 0 RD 192.168.0.17 GigabitEthernet 0/0/0192.168.0.112/28 Static 60 0 RD 192.168.0.17 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.34 GigabitEthernet 0/0/1192.168.0.128/28 Static 60 0 RD 192.168.0.17 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.34 GigabitEthernet 0/0/1
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R2]R3路由表
[R3]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: PublicDestinations : 22 Routes : 24 Destination/Mask Proto Pre Cost Flags NextHop Interface100.1.1.0/24 Static 60 0 RD 192.168.0.66 GigabitEthernet 4/0/0Static 60 0 RD 192.168.0.50 GigabitEthernet 0/0/2127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0192.168.0.0/28 Static 60 0 RD 192.168.0.33 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.81 GigabitEthernet 0/0/1192.168.0.16/28 Static 60 0 RD 192.168.0.33 GigabitEthernet 0/0/0192.168.0.32/28 Direct 0 0 D 192.168.0.34 GigabitEthernet 0/0/0192.168.0.34/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.47/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.48/28 Direct 0 0 D 192.168.0.49 GigabitEthernet 0/0/2192.168.0.49/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/2192.168.0.63/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/2192.168.0.64/28 Direct 0 0 D 192.168.0.65 GigabitEthernet 4/0/0192.168.0.65/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 4/0/0192.168.0.79/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 4/0/0192.168.0.80/28 Direct 0 0 D 192.168.0.82 GigabitEthernet 0/0/1192.168.0.82/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.95/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.96/28 Static 60 0 RD 192.168.0.81 GigabitEthernet 0/0/1192.168.0.112/28 Static 60 0 RD 192.168.0.81 GigabitEthernet 0/0/1192.168.0.128/28 Static 60 0 RD 192.168.0.81 GigabitEthernet 0/0/1
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R3]R4路由表
[R4]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: PublicDestinations : 16 Routes : 16 Destination/Mask Proto Pre Cost Flags NextHop Interface100.1.1.0/24 Static 60 0 RD 192.168.0.82 GigabitEthernet 0/0/0127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0192.168.0.0/28 Static 60 0 RD 192.168.0.97 GigabitEthernet 0/0/1192.168.0.16/28 Static 60 0 RD 192.168.0.97 GigabitEthernet 0/0/1192.168.0.32/28 Static 60 0 RD 192.168.0.82 GigabitEthernet 0/0/0192.168.0.48/28 Static 60 0 RD 192.168.0.82 GigabitEthernet 0/0/0192.168.0.64/28 Static 60 0 RD 192.168.0.82 GigabitEthernet 0/0/0192.168.0.80/28 Direct 0 0 D 192.168.0.81 GigabitEthernet 0/0/0192.168.0.81/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.95/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.96/28 Direct 0 0 D 192.168.0.98 GigabitEthernet 0/0/1192.168.0.98/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.111/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R4]R5路由表
[R5]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: PublicDestinations : 20 Routes : 27 Destination/Mask Proto Pre Cost Flags NextHop Interface100.1.1.0/24 Direct 0 0 D 100.1.1.2 GigabitEthernet 0/0/2100.1.1.2/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/2100.1.1.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/2127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0192.168.0.0/28 Static 60 0 RD 192.168.0.65 GigabitEthernet 0/0/1Static 60 0 RD 192.168.0.49 GigabitEthernet 0/0/0192.168.0.16/28 Static 60 0 RD 192.168.0.65 GigabitEthernet 0/0/1Static 60 0 RD 192.168.0.49 GigabitEthernet 0/0/0192.168.0.32/28 Static 60 0 RD 192.168.0.65 GigabitEthernet 0/0/1Static 60 0 RD 192.168.0.49 GigabitEthernet 0/0/0192.168.0.48/28 Direct 0 0 D 192.168.0.50 GigabitEthernet 0/0/0192.168.0.50/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.63/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0192.168.0.64/28 Direct 0 0 D 192.168.0.66 GigabitEthernet 0/0/1192.168.0.66/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.79/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/1192.168.0.80/28 Static 60 0 RD 192.168.0.49 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.65 GigabitEthernet 0/0/1192.168.0.96/28 Static 60 0 RD 192.168.0.49 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.65 GigabitEthernet 0/0/1192.168.0.112/28 Static 60 0 RD 192.168.0.49 GigabitEthernet 0/0/0Static 60 0 RD 192.168.0.65 GigabitEthernet 0/0/1192.168.0.128/28 Static 60 0 RD 192.168.0.65 GigabitEthernet 0/0/1Static 60 0 RD 192.168.0.49 GigabitEthernet 0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R5]R6路由表
[R6]display ip routing-table
Route Flags: R - relay, D - download to fib
------------------------------------------------------------------------------
Routing Tables: PublicDestinations : 16 Routes : 16 Destination/Mask Proto Pre Cost Flags NextHop Interface100.1.1.0/24 Direct 0 0 D 100.1.1.1 GigabitEthernet 0/0/0100.1.1.1/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0100.1.1.255/32 Direct 0 0 D 127.0.0.1 GigabitEthernet 0/0/0127.0.0.0/8 Direct 0 0 D 127.0.0.1 InLoopBack0127.0.0.1/32 Direct 0 0 D 127.0.0.1 InLoopBack0
127.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0192.168.0.0/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.16/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.32/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.48/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.64/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.80/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.96/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.112/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0192.168.0.128/28 Static 60 0 RD 100.1.1.2 GigabitEthernet 0/0/0
255.255.255.255/32 Direct 0 0 D 127.0.0.1 InLoopBack0[R6]其实这里已经可以检测上面路由器之间是否通没通用R1去pingR6
[R1]ping 100.1.1.1PING 100.1.1.1: 56 data bytes, press CTRL_C to breakRequest time outReply from 100.1.1.1: bytes56 Sequence2 ttl252 time80 msReply from 100.1.1.1: bytes56 Sequence3 ttl252 time40 msReply from 100.1.1.1: bytes56 Sequence4 ttl252 time30 msReply from 100.1.1.1: bytes56 Sequence5 ttl252 time40 ms--- 100.1.1.1 ping statistics ---5 packet(s) transmitted4 packet(s) received20.00% packet lossround-trip min/avg/max 30/47/80 ms[R1]4、配置DHCP服务
R4实现代码
[R4]dh
[R4]dhcp en
[R4]dhcp enable
Info: The operation may take a few seconds. Please wait for a moment.done.
[R4]ip p
[R4]ip policy-based-route
[R4]ip pool 1
#Info: Its successful to create an IP address pool.
[R4-ip-pool-1]net
[R4-ip-pool-1]netbios-type
[R4-ip-pool-1]network 192.168.0.112 m
[R4-ip-pool-1]network 192.168.0.112 mask 28
[R4-ip-pool-1]g
[R4-ip-pool-1]gateway-list 192.168.0.113
[R4-ip-pool-1]dn
[R4-ip-pool-1]dns-list 8.8.8.8
[R4-ip-pool-1]quit
[R4]ip p
[R4]ip policy-based-route
[R4]ip pool 2
Info: Its successful to create an IP address pool.
[R4-ip-pool-2]n
[R4-ip-pool-2]nbns-list
[R4-ip-pool-2]netbios-type
[R4-ip-pool-2]network 192.168.0.128 m
[R4-ip-pool-2]network 192.168.0.128 mask 28
[R4-ip-pool-2]g
[R4-ip-pool-2]gateway-list 192.168.0.129
[R4-ip-pool-2]dn
[R4-ip-pool-2]dns-list 8.8.8.8
[R4-ip-pool-2]quit
[R4]int g0/0/2.1
[R4-GigabitEthernet0/0/2.1]dh
[R4-GigabitEthernet0/0/2.1]dhcp s
[R4-GigabitEthernet0/0/2.1]dhcp select g
[R4-GigabitEthernet0/0/2.1]dhcp select global
[R4-GigabitEthernet0/0/2.1]int g0/0/2.2
[R4-GigabitEthernet0/0/2.2]dhcp select global
[R4-GigabitEthernet0/0/2.2]quit
[R4]int g0/0/2.1
[R4-GigabitEthernet0/0/2.1]do
[R4-GigabitEthernet0/0/2.1]dot1q t
[R4-GigabitEthernet0/0/2.1]dot1q termination v
[R4-GigabitEthernet0/0/2.1]dot1q termination vid 2
Jul 17 2023 17:47:36-08:00 R4 %%01IFNET/4/LINK_STATE(l)[2]:The line protocol IP
on the interface GigabitEthernet0/0/2.1 has entered the UP state.
[R4-GigabitEthernet0/0/2.1]int g0/0/2.2
[R4-GigabitEthernet0/0/2.2]do
[R4-GigabitEthernet0/0/2.2]dot1q t
[R4-GigabitEthernet0/0/2.2]dot1q termination v
[R4-GigabitEthernet0/0/2.2]dot1q termination vid 3
Jul 17 2023 17:48:04-08:00 R4 %%01IFNET/4/LINK_STATE(l)[3]:The line protocol IP
on the interface GigabitEthernet0/0/2.2 has entered the UP state.
[R4-GigabitEthernet0/0/2.2]quit
[R4]int g0/0/2.1
[R4-GigabitEthernet0/0/2.1]arp t
[R4-GigabitEthernet0/0/2.1]arp b
[R4-GigabitEthernet0/0/2.1]arp broadcast en
[R4-GigabitEthernet0/0/2.1]arp broadcast enable
[R4-GigabitEthernet0/0/2.1]int g0/0/2.2
[R4-GigabitEthernet0/0/2.2]arp b
[R4-GigabitEthernet0/0/2.2]arp broadcast en
[R4-GigabitEthernet0/0/2.2]arp broadcast enable
[R4-GigabitEthernet0/0/2.2]quit
[R4]5、测试 6、优化
1、配置缺省路由 R1实现代码
[R1]ip ro
[R1]ip route
[R1]ip route-static 0.0.0.0 0 192.168.0.18
[R1]ip route-static 0.0.0.0 0 192.168.0.98
[R1]R2实现代码
[R2]ip ro
[R2]ip route
[R2]ip route-static 0.0.0.0 0 192.168.0.34
[R2]R3实现代码
[R3]ip ro
[R3]ip route
[R3]ip route-static 0.0.0.0 0 192.168.0.66
[R3]ip route-static 0.0.0.0 0 192.168.0.50
[R3]R4实现代码
[R4]ip ro
[R4]ip route
[R4]ip route-static 0.0.0.0 0 192.168.0.82
[R4]R5实现代码
[R5]
[R5]ip ro
[R5]ip route
[R5]ip route-static 0.0.0.0 0 100.1.1.1
[R5]2、配置空接口防环 R1实现代码
[R1]ip ro
[R1]ip route
[R1]ip route-static 192.168.0.0 28 NU
[R1]ip route-static 192.168.0.0 28 NULL 0
[R1]
